Differences

This shows you the differences between two versions of the page.

--- proxmox_ipv6 [2016/07/17 10:23] – neoon
+++ proxmox_ipv6 [2021/12/05 14:14] (current) – neoon
@@ Line 1: / Line 1: @@
 If you have a Kimsufi Dedicated, you got a full /64 not just /128 which is a single IP, lets use it.
-First we need to enable Forwarding on the Node:
-  net.ipv6.conf.all.forwarding = 1
-  net.ipv6.conf.all.proxy_ndp = 1
-  net.ipv6.bindv6only = 1
 Next, we need to add IPv6 to our vmbr2, which the VM should be connected to.
-  auto vmbr2
   iface vmbr2 inet6 static
-  address 2601:xxxx:xx:xxx::2
+       address 2601:xxxx:xx:xxx::2
-  netmask 64
+       netmask 64
-  bridge_ports none
+       bridge_ports none
-  bridge_stp off
+       bridge_stp off
-  bridge_fd 0
+       bridge_fd 0
-  post-up echo 1 > /proc/sys/net/ipv6/conf/all/proxy_ndp
+       post-up echo 1 > /proc/sys/net/ipv6/conf/all/proxy_ndp
-  post-up echo 1 > /proc/sys/net/ipv6/conf/all/forwarding
+       post-up echo 1 > /proc/sys/net/ipv6/conf/all/forwarding
-  post-up echo 1 > /proc/sys/net/ipv6/conf/default/forwarding
+       post-up echo 1 > /proc/sys/net/ipv6/conf/default/forwarding
-  post-up /sbin/ip -f inet6 neigh add proxy 2601:xxxx:xx:xxx::2 dev vmbr2
+       post-up /sbin/ip -f inet6 neigh add proxy 2601:xxxx:xx:xxx::2 dev vmbr2
-  post-up /sbin/ip -f inet6 neigh add proxy 2601:xxxx:xx:xxx::3 dev vmbr0
+       post-up /sbin/ip -f inet6 neigh add proxy 2601:xxxx:xx:xxx::3 dev vmbr0
-  post-up /sbin/ip -f inet6 route add 2601:xxxx:xx:xxx::3 dev vmbr2
+       post-up /sbin/ip -f inet6 route add 2601:xxxx:xx:xxx::3 dev vmbr2
+The next thing you need to do, restart your network on your Dedi with:
-The next thing you need to do, restart your network with: service networking restart
+   service networking restart
+Now Login into your VM and add this to your /etc/network/interfaces:
+  iface eth0 inet6 static
+       address 2601:xxxx:xx:xxx::3
+       netmask 64
+       gateway 2601:xxxx:xx:xxx::2
+Restart your Networking on the VM:
+   service networking restart
+If it dosen't respond after a while, try to Reboot your VM over Proxmox.
+Now we still need to add IPv6 DNS Server to our /etc/resolv.conf:
+:4860:4860::8888
+:4860:4860::8844
+These are the IPv6 Nameservers from Google but you can use different ones.
+If you run:
+  ping6 google.com
+You should get a response and you should be able to reach your VM under this IPv6 which you configured earlier.
 Sources used: http://hw7.net/?p=252