Differences

This shows you the differences between two versions of the page.

--- docker_cluster [2024/10/21 01:08] – neoon
+++ docker_cluster [2024/10/21 15:29] (current) – neoon
@@ Line 25: / Line 25: @@
 **4**. Enable GlusterFS
-  systemctl start glusterd
+  systemctl start glusterd && systemctl enable glusterd
-  systemctl enable glusterd
 **5**. Peer with your GlusterFS nodes
@@ Line 36: / Line 35: @@
   gluster peer status
-**7.** Create your first volume for Docker
+**7.** Folders for the mount
-  mkdir -p /mnt/bricks/docker
+  mkdir -p /mnt/bricks/docker &&   mkdir -p /mnt/data/docker
+**8.** Create your first volume for Docker
   gluster volume create docker replica 3 10.0.1.1:/mnt/bricks/docker 10.0.2.1:/mnt/bricks/docker 10.0.3.1:/mnt/bricks/docker force
+  gluster volume start docker
-**8**. Mount your first volume
+**9**. Mount your first volume
-  mkdir -p /mnt/data/docker
   mount.glusterfs 10.0.X.1:/docker /mnt/data/docker
-**9**. Make the mount boot ready
+**10**. Make the mount boot ready
   [Unit]
@@ Line 61: / Line 62: @@
 Copy this to /etc/systemd/system/mounts.service
-**10**. Enable the mount service
+**11**. Enable the mount service
   systemctl enable mounts
-**11**. You may have to edit the GlusterFS systemd file to prevent a race condition with your VPN. \\
+**12**. You may have to edit the GlusterFS systemd file to prevent a race condition with your VPN. \\
 GlusterFS will fail to start if your VPN isn't running already.
@@ Line 74: / Line 75: @@
 Profit! Next reboot GlusterFS should start up fine.
-**12**. Install Docker
+**13**. Install Docker
   # Add Docker's official GPG key:
@@ Line 87: / Line 88: @@
   apt-get update && apt-get install docker-ce docker-ce-cli containerd.io docker-buildx-plugin docker-compose-plugin -y
-**13**. Init the Swarm on the first Node
+**14**. Init the Swarm on the first Node
   docker swarm init --advertise-addr 10.0.1.1 --listen-addr=10.0.1.1
 advertise-addr will only advertise the swarm inside our VPN network
-**14**. Join other Nodes
+**15**. Join other Nodes
   docker swarm join --token whateverthattokenis 10.0.1.1:2377 --listen-addr=10.0.2.1
   docker swarm join --token whateverthattokenis 10.0.1.1:2377 --listen-addr=10.0.3.1
 listen-addr will force swarm to bind to your local VPN
-**15**. Promote the other Nodes to archive 100% True HA
+**16**. Check the Cluster
+  docker node ls
+**17**. Promote the other Nodes to archive 100% True HA
   docker node promote node2
   docker node promote node3
-**16**. Deploy your first service \\
+**18**. Deploy your first service \\
 In my case it was a ZNC bouncer. \\
 Had to run the docker container normally to generate the config files. \\
@@ Line 108: / Line 112: @@
 Lets deploy the service.
   docker service create --mount type=bind,src=/mnt/data/docker/znc/,dst=/znc-data --publish published=1025,target=1025 --name bouncer znc
+The service will get exposed on port 1025 on all nodes.
-**17**. If you run this, on any node.
+**19**. If you run this, on any node.
   docker node ps $(docker node ls -q)
 You should be able to check your container status.
-**18**. When you reboot the mentioned node above, the service should be restored in about 60s.
+**20**. When you reboot the node with your container, the service should be restored in about 60s.